Please select your home edition
Edition
Wessex Resins 2019 - Pro-Set - 728x90

Avoiding the epoxy 'orange peel' effect - advice from Wessex Resins & Adhesives

by Jake Kavanagh 26 Dec 2018 12:00 GMT
You've applied a fresh coat of epoxy and the coat seems to have fish-eyed into a series of tiny craters! © WSI

You've applied a fresh coat of epoxy and the coat seems to have fish-eyed into a series of tiny craters. What has caused this and how do you prevent it from happening again?

"The piece of wood in the photo is typical of what can happen when it hasn't been properly prepared for epoxy coating," epoxy expert Hamish says. "This is a piece of mahogany and the customer explained that it had been originally coated with polyurethane varnish. This was removed using paint stripper and the piece was thoroughly abraded back to bare wood. Then a coat of WEST SYSTEM® 105 Resin with 207 Special Coating Hardener was applied. (The 105/207 epoxy mix is used when the wood is to be varnished, as it brings out the full luster of the grain). This orange peel effect was noticed shortly afterwards, so what has happened?

The epoxy has been contaminated. This is because abrading back to bare wood is only part of the preparation process. Despite fresh timber being exposed, it could still contain trapped solvents from the original coating, as well as natural oils. Teak is a naturally oily wood and oak also contains sap-based chemicals that can affect the final surface finish.

The best way to eliminate contamination is to ensure all previous coatings have been completely removed. This can be done with chemical stripping, as seen here, or abrasion. Once the wood is completely bare again then it will need a wash to remove the chemicals used.

WEST SYSTEM 855 Cleaning Solution has been specially formulated for this job and is also very good for removing uncured epoxy from workbenches, or amine blush from cured coatings. If you don't have any 855 to hand, then you can also use clean fresh water but avoid any detergents or soaps, which could actually put contaminants back into the wood. As shown in the picture, both the 855 Cleaning Solution and 850 Cleaning Solvent (for final preparation) are available in A and B pack sizes.

With the wood completely dry, prepare the surface for epoxy coating by abrading again. The grit used should be fine (180 400) as you will need to eradicate any swirl marks from previous coarse sanding, especially if that is how you removed the original coating. A smooth finish will give the best results so hand-sanding with the grain is ideal.

Brush off the dust and then wash the timber again but this time with a solvent. You can use acetone but avoid any spirit-based solvents. Formulations like household White Spirit are packed with oils that will compromise the coating.

WEST SYSTEM 850 Cleaning Solvent is a blend of solvents and will not leave a greasy residue. This has been designed for the best decontamination before overcoating and as it is a blend of solvents the flash-off time has been reduced, so cleaning can be done at a more leisurely pace.

TOP TIP: (This applies to any kind of chemically assisted cleaning.) Don't place the cleaning cloth over the mouth of the solvent container when wetting the cleaning cloth. We've all done it but after a few wipes, dirt and oils on the cloth are washed back into the container to contaminate the solvent. Best practice is to decant a little into a jar and use that instead, ensuring a clean section of cloth is used for each pass.

Don't overlook your brushes and rollers. A common mistake in DIY workshops is to leave these items lying around, perhaps in a jar on the workbench, or in an open pack. Any airborne contaminates from aerosol polishes, WD40, or even airborne cooking oils from a nearby extractor fan, can settle on your rollers and later often much later affect the coating. Keep your brushes and rollers sealed up until you are ready to use them.

The same applies to mixing pots. These are often left stacked upright. Turn them upside down so no dust or airborne contaminants can settle inside. Also, don't trust a pot that has been 'cleaned' unless it was with 855 Cleaning Solution. This is very true of recycled food containers that may have been washed out with detergent or contaminated kitchen cloths. Always use a brand new mixing pot, or one that is scrupulously clean.

It's also a good idea to wear gloves during the preparation process. Although very rare, some hand creams, soaps and even sweat can cause localised problems if absorbed into the virgin timber.

And if you do get orange peel don't despair. Let if cure and then simply abrade it off and start again, this time taking care not to re-contaminate. The end result is worth the effort!

See more tips at: epoxycraft.com/category/blog

Related Articles

Fire Retardant Additive for Epoxy Resin
Does what it says on the tin WEST SYSTEM 421 Fire Retardant Additive does what it says on the tin - it retards fire. It is a heavy, non-combustible powder that is added to a fresh mix of epoxy. Posted on 1 Aug
Building an 18th century Gajeta part 7
Modern epoxy techniques on a classic design After several months of intense boatbuilding, the craftsmen at the Betina Shipyard in Croatia are in the final stages of the completing their experimental 7-metre traditional sailing gajeta. Posted on 29 Jul
Happy Birthday to Gougeon Brothers, Inc
Creators of West System epoxy celebrate 50 years Wessex Resins & Adhesives manufacture WEST SYSTEM®, PRO-SET® and ENTROPY RESINS® under licence from the Gougeon Brothers Inc, USA. Below Grace Ombry traces the company's heritage, from its modest beginnings as a boat shop... Posted on 5 Jul
Tips from the Epoxy Professionals
Preparing teak strips for bonding Here's a tip for preparing a teak plank for a small-scale project such as a cockpit table. It could work just as well on a complete deck. Mark at Aquamarine Ltd uses it whenever he wants to bond teak to a substrate (no screws). Posted on 2 Jun
Making a Mouse Boat with Oarsome Chance
Disadvantaged boat-building students use just one sheet of plywood Wessex Resins and Adhesives is a proud sponsor of the charity Oarsome Chance, where disadvantaged and school-excluded young adults learn how to build and repair boats and use them on the water. Instructor Nick Hart describes the making of a 'Mouse Boat'. Posted on 31 May
Raising the bar with Entropy Resins
A sailing club bar top with a nautical theme James Case has been a member of Wells Sailing Club since he was a child. "It's always had the same bar," he says, "but when the club decided to do a major refit, we decided to make a new bar with a nautical theme." Posted on 28 May
Bio-based epoxy resin now available in Europe
Manufacturers of West System epoxy now sell Entropy Resins too Wessex Resins & Adhesives is delighted to announce the launch of a new online store to facilitate ordering the unique range of bio-based epoxy: ENTROPY RESINS. The EU online store has been added to the current North American website. Posted on 19 May
Fixing hull battens with West System Expoxy
A dab of 'five minute epoxy' holds things whilst the main epoxy bond sets When building or repairing, a strategic dab of WEST SYSTEM G5 Epoxy (sometimes known as five-minute epoxy) will greatly speed up the job of securing a workpiece, whilst the structural epoxy used in the process cures. Posted on 9 May
Building an 18th century Gajeta part 6
A traditional style boat with modern epoxy construction The tough and seaworthy gajeta is powered by a lanteen sail and a small inboard engine. This graphic shows the internal design, including the small forepeak cabin and was posted onto the workshop wall as inspiration. Posted on 6 May
Building an 18th century Gajeta part 4
A merger of CNC parts, epoxy resin and traditional skills A gajeta is a traditional design of small open fishing boat but as they are raced competitively, an enterprising naval architect decided to make one using modern epoxy techniques. In this instalment, the computer-generated design is taking shape. Posted on 22 Mar