Rossiter Pintail Mortagne sur Gironde, near Bordeaux |
![]() |
Laser 28 - Excellent example of this great design Hamble le rice |
![]() |
List classes of boat for sale |
Pro-Grip Goo |
Post Reply ![]() |
Page 12> |
Author | |
Hengest ![]() Groupie ![]() ![]() Joined: 05 Jun 06 Location: United Kingdom Online Status: Offline Posts: 77 |
![]() ![]() ![]() ![]() Posted: 28 Mar 19 at 12:30pm |
I used screwfix spray aerosol on my 600 last year. It hasn't fallen off yet.
|
|
![]() |
|
Alistair426 ![]() Far too distracted from work ![]() Joined: 02 Jun 08 Location: Vatican City State Online Status: Offline Posts: 201 |
![]() ![]() ![]() ![]() |
Cheers, Riv. That was the sort of stuff I was looking at.
Edited by Alistair426 - 27 Mar 19 at 8:57am |
|
![]() |
|
Riv ![]() Far too distracted from work ![]() Joined: 23 Nov 13 Location: South Devon Online Status: Offline Posts: 353 |
![]() ![]() ![]() ![]() |
Did my Race board with Yoga mat and this contact spray adhesive. Worked fine. https://www.toolstation.com/spray-contact-adhesive/p47790
|
|
Mistral Div II prototype board, Original Windsurfer, Hornet built'74.
|
|
![]() |
|
Alistair426 ![]() Far too distracted from work ![]() Joined: 02 Jun 08 Location: Vatican City State Online Status: Offline Posts: 201 |
![]() ![]() ![]() ![]() |
Chris,
Several of the aerosols used to fit carpeting to the interiors of vans are two-part (I assume you meant 'apply to both sides and wait') and shown as waterproof and high temperature resistant (you know how hot the inside of a black van can get). Obviously not getting a big thumbs-up on here, though.
Edited by Alistair426 - 26 Mar 19 at 9:28am |
|
![]() |
|
Paramedic ![]() Really should get out more ![]() Joined: 27 Jan 06 Location: United Kingdom Online Status: Offline Posts: 929 |
![]() ![]() ![]() ![]() |
in my experience the only contact adhesives that work long term are two part products. so that rules out aerosols!
|
|
![]() |
|
Alistair426 ![]() Far too distracted from work ![]() Joined: 02 Jun 08 Location: Vatican City State Online Status: Offline Posts: 201 |
![]() ![]() ![]() ![]() |
Hope this doesn't count as a hijack but has anybody used spray contact adhesive to apply Progrip? If so, what brand? There appears to be a lot of variety in cost and I assume, quality of glue.
|
|
![]() |
|
piglet ![]() Really should get out more ![]() Joined: 04 Jan 07 Online Status: Offline Posts: 514 |
![]() ![]() ![]() ![]() |
Toluene
|
|
![]() |
|
ClubRacer ![]() Far too distracted from work ![]() Joined: 26 Sep 15 Online Status: Offline Posts: 210 |
![]() ![]() ![]() ![]() |
A new 25mm chisel is wide and sharp enough that it wont even mark the boat if wielded well
Then just go to town with a scouring pad and any solvent. If you're struggling for a solvent a good easy one to get hold of is cellulose thinners from Halfords Exactly the same setup for doing slot gaskets plus a little sand on the stubborn bits. Just make sure your chisel is a dedicated boat chisel as the minute you blunt or dent it you'l start leaving marks on the boat This is for GRP, never had to do it to anything else
|
|
![]() |
|
Daniel Holman ![]() Really should get out more ![]() Joined: 17 Nov 08 Online Status: Offline Posts: 997 |
![]() ![]() ![]() ![]() |
No sweat. If you are going back on with pro grip then polished surface not too vital :-)
If chisel sharp and wielded well it should not mark the surface. My racks are natural carbon finish. |
|
![]() |
|
ifoxwell ![]() Really should get out more ![]() ![]() Joined: 05 Jan 06 Location: Hoo Online Status: Offline Posts: 669 |
![]() ![]() ![]() ![]() |
Thanks Dan. Its on GRP so i'm not to keen on the chisel but i do have acetone
|
|
RS300
|
|
![]() |
Post Reply ![]() |
Page 12> |
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |