Please select your home edition
Edition
upffront 2018 Millionaires Tape 728x90

Measuring a Torsional Cable: Tackle Luff Length Troubles

by Kerri Robson 15 May 09:00 BST
Doyle tack plate © Doyle Oleu Sailmakers

Previously on the upffront.com blog, we looked at how to measure a new torsional cable for your boat, and emphasised the importance of an accurate measurement to ensure a correct cable specification for your new code zero or downwind asymmetric.

When top-down furling asymmetric gennakers, the sail is 'fixed' to the cable at the head only and, as a result, cable length is relatively independent of sail luff length instead determined by the maximum available space between the tack and full hoist point.

However, for code zeros, the cable is fixed to the sail at both the tack and the head - and therefore the cable must perfectly match the sail luff length.

This can be a challenge: luff load (and therefore luff length) can vary considerably depending on wind strength and sailing angle. In addition, with the cable lashed to the sail at both ends, increasing and decreasing cable load can directly impact the luff tension in the sail cloth.

If the sail is too tight on the cable, the sailcloth can be overstretched. In contrast, if the sail is too loose, the sail luff will not be tight enough at maximum cable tension.

To overcome this, traditionally the sailmaker would order the torsional cable slightly overlength, and then during setup and initial sea-trails adjust the head lashing to provide the correct sail luff tension at maximum cable load.

However, to simplify and de-risk the challenge of matching cable to sail luff, an increasingly popular choice with sailmakers is to turn the problem on its head, with many choosing instead to make the cable significantly shorter than the sail luff length!

But how does this work?

Instead of having the tack lashed tightly to the cable thimble and making the required adjustment at the head, the head is fixed tightly instead. This leaves the cable short of the tack (by approx. 2-3% of luff length) and a lashing is used between the bottom of the cable and a special tack plate on the sail.

For this system to work, the introduction of the tack plate is essential: it allows space for both the lashing to the cable and attachment to the drum, plus integrates slots for webbing (at various angles) to fully integrate it into the tack patch.

Consequently, at the start of the furl, it is the tack plate and the tack patch rather than the cable which initial the furl; once the cable is wrapped into the tack patch, the torque is transmitted up the luff of the sail.

As the cable is 300-500mm shorter than the sail length, there is a much greater safety margin with regards to matching cable to sail luff. In addition, tuning and adjustment becomes much easier, as this is now done at the tack rather than the head and can be adapted whilst sailing.

Finally, it also allows the sail to be built to maximise full luff length, as opposed to slightly shorter due to the length of the lashing at the head.

If you have any questions or need any help with a measurement on board, please get in touch with us using our Furling Enquiry Form.

Related Articles

New in Genoa Sail Furling
Facnor LS/LX/RX available at upffront.com We've said it before, and we'll say it again: here at Upffront we are passionate about lighter, faster and safer sailing. As a result, we are constantly searching for performance orientated solutions that will optimise sailing for all. Posted today at 8:00 am
nke Marine Electronics - Do I really need Wi-Fi?
Have your phone or tablet display wind, speed, and more More sailors are jumping on board with performance enhancing marine electronics than ever before, and we've had an influx of enquiries since adding nke Marine Electronics to upffront.com. Posted on 20 May
Measuring Your Boat for a New Torsional Cable
Process for getting an accurate result You have decided to go for a new code zero or downwind asymmetric. To ensure the furling system fits your boat, it is important to take a physical measurement of the maximum space available from the drum to the full hoist position. Posted on 10 May
Furling Drum Locks - to lock, or not to lock?
Advantages, drawbacks, and different methods to use There is somewhat of a debate over the use of drum locks on a continuous line furling drum. As it says on the tin, a drum lock is designed to lock a continuous line furling drum in place, in order to prevent accidental unfurling. Posted on 3 May
Explore the Spinlock Rope Clutch Range
Some of the best high-performance clutches on the market: XAS, XTS, XCS Exploring the Spinlock range, the XAS rope clutch is a multi-role clutch with excellent performance across a wide rope range. It comes in two sizes: 4mm – 8mm, which has a maximum load of 400KG, and 6mm – 12mm, which has a maximum load of 575KG. Posted on 26 Apr
Reducing Weight Aloft with Composite Backstays
Simple replacement offerring superior performance over wire Reducing weight aloft is one of the most cost effective ways of increasing your boat speed and performance: every kilogram you take out of the rig is roughly equivalent to 4kg added to the bottom of your keel. Posted on 22 Apr
PROtect Tapes take on regatta plastic pollution
Biodegradable and compostable hull stickers available Experts at creating products designed to tackle chafing, abrasion, scratches, damages, ageing, and wear, PROtect Tapes have now honed their unique technical film know-how to create biodegradable and compostable bow and hull stickers Posted on 17 Apr
Fresh In - Tiller Extensions
From three big players: Spinlock, Harken and Ronstan We are excited to now introduce six ranges of tiller extensions on upffront.com, from three big players: Spinlock, Harken and Ronstan. Posted on 15 Apr
Dyneema Braided Cover
The latest addition to your tool kit Dyneema® is the strongest fibre in the world. Ten times stronger than steel, and seven to ten times lighter than a steel wire of equivalent size, Dyneema® is one of the most durable and sought-after materials on the sailing market. Posted on 8 Apr