New Posts New Posts RSS Feed: Best rope for main halyard
  FAQ FAQ  Forum Search   Register Register  Login Login

Best rope for main halyard

 Post Reply Post Reply Page  <1 23456>
Author
Medway Maniac View Drop Down
Really should get out more
Really should get out more
Avatar

Joined: 13 May 05
Location: United Kingdom
Online Status: Offline
Posts: 2786
Post Options Post Options   Quote Medway Maniac Quote  Post ReplyReply Direct Link To This Post Posted: 17 Mar 09 at 5:48pm

But with a 1:1 halyard, the tension in the halyard running down the mast is by definition the same as the tension in the bit of halyard tied to the sail-head (less any minimal losses due to friction in the pulley). You will therefore have 2xT compressing the mast at least between the mast-head pulley and the gooseneck area, assuming the cleat is at or below the gooseneck.

Now, move your cleat up to the masthead (to effectively provide a halyard lock) and there's only 1xT acting between the mast-head and gooseneck area, namely that efected by the sail (we're neglecting standing rigging loads etc. here, obviously).

Put a 2:1 on the sail head and dead-end it at the mast-head and we'll have a lower tension in the halyard. Thus the compressive force will be that produced by the sail plus the lower tension in the 2:1'd halyard, hence lower compression than with a simple 1:1 halyard.

Back to Top
alstorer View Drop Down
Really should get out more
Really should get out more
Avatar

Joined: 02 Aug 07
Location: Cambridge
Online Status: Offline
Posts: 2899
Post Options Post Options   Quote alstorer Quote  Post ReplyReply Direct Link To This Post Posted: 17 Mar 09 at 6:09pm
If a 2:1 didn't reduce compression compared to a 1:1, it also wouldn't make it any easier to pull the sail up- the force involved, after all, comes from the same source...
-_
Al
Back to Top
craiggo View Drop Down
Really should get out more
Really should get out more
Avatar

Joined: 01 Apr 04
Location: United Kingdom
Online Status: Offline
Posts: 1810
Post Options Post Options   Quote craiggo Quote  Post ReplyReply Direct Link To This Post Posted: 18 Mar 09 at 8:21am
Yes & No.

Moving the halyard cleat up the mast reduces the exposed length of mast over which the force is acting. However multiple purchases will not reduce the overall force between the head of the sail and the block at the top of the mast, they simply divide the force up over all the runs out of the blocks. The overall force holding the sail up is still the same.
Once the blocks are all block to block you loose most, if not all of your mechanical advantage and the load on the tail of the halyard running down the mast will become almost the same as the force holding the sail up.

Your theory works absolutely fine assuming that you dont pull your main all the way up, however in doing this you expose much larger lengths of halyard to stretch.

Back to Top
Medway Maniac View Drop Down
Really should get out more
Really should get out more
Avatar

Joined: 13 May 05
Location: United Kingdom
Online Status: Offline
Posts: 2786
Post Options Post Options   Quote Medway Maniac Quote  Post ReplyReply Direct Link To This Post Posted: 18 Mar 09 at 9:45am

In practice you don't get the 2:1 halyard "block -to-block" (there are no blocks, of course), and there are exposed lengths of halyard between the mast-top pulley and the sail head (I've never seen otherwise), so the halyard  tension and compression remain reduced.

But I think you've now got the point.

Back to Top
Peaky View Drop Down
Really should get out more
Really should get out more


Joined: 15 Nov 08
Location: United Kingdom
Online Status: Offline
Posts: 2771
Post Options Post Options   Quote Peaky Quote  Post ReplyReply Direct Link To This Post Posted: 18 Mar 09 at 9:58am

MM is right. 

A cat-style halyard lock does reduce mast compression, as well as eliminate halyard stretch/slip.

A 1:1 halyard has twice the compressive load of a halyard lock.

A 2:1 halyard has 1.5 times the compressive load of a halyard lock, or 0.75 times the compressive load of a 1:1 system.  Some of that gain will be lost due to system inefficiency, but there is still a gain.  However, you do end up with another 6m of rope to stow!

 



Edited by Peaky
Back to Top
Jamesd View Drop Down
Far too distracted from work
Far too distracted from work


Joined: 01 Feb 08
Online Status: Offline
Posts: 377
Post Options Post Options   Quote Jamesd Quote  Post ReplyReply Direct Link To This Post Posted: 18 Mar 09 at 11:11am

all this is confusing and im struggling to understand.

I mean Peaky, since when has a halyard been used in compression? rope would buckle almost immediately in compression. i know, you mean the mast has compressive forces.

with 100kN acting downwards on a mast from the sail you then have 50kN running down the mast in the halyard (if 2:1) therefore to resist the force the deck must produce a reaction, of 150kN, or the sail and mast will come out the bottom of the boat. the mast acts as a compressive member. thats all very well and good.

but what about the 50kN acting downwards at the dead end of the knot at the top of the mast, that brings the total downward force to 200kN thus the compression in the mast must be 200kN which is the same as a 1:1. the 2:1 will be easier to pull up and would require less of a reaction to hold it up there (think of a mainsheet and the difference of 1:1 and multiple purchases), but mast compression does not change.

locking the sail at the top of the mast reduces the compression as you can neglect the halyard loads acting downwards and therefore a smaller reaction is needed.

I think thats all right, my head is spinning to be honest.

Lol ive just confused myself even more.

in reality though, though the compression forces acting down do not run down the centre of the mast. they are offset (the sail at the top) causing a moment and initiating a buckle in the mast and thus the trailing edge of the mast carries compressive load and the front edge will be under tension.

plus there are many many more factors to think of, such as the fact the force on the sail is a vector not just a parrallel force

Back to Top
Medway Maniac View Drop Down
Really should get out more
Really should get out more
Avatar

Joined: 13 May 05
Location: United Kingdom
Online Status: Offline
Posts: 2786
Post Options Post Options   Quote Medway Maniac Quote  Post ReplyReply Direct Link To This Post Posted: 18 Mar 09 at 11:39am
Originally posted by Jamesd

all this is confusing and im struggling to understand.

I mean Peaky, since when has a halyard been used in compression? rope would buckle almost immediately in compression. i know, you mean the mast has compressive forces. Yes, it's the mast in compression, under load from the halyard/sail, not the halyard; that's what I understand Peaky to be saying.

with 100kN acting downwards on a mast from the sail you then have 50kN running down the mast in the halyard (if 2:1) therefore to resist the force the deck must produce a reaction, of 150kN, or the sail and mast will come out the bottom of the boat. the mast acts as a compressive member. thats all very well and good. Yes, except unless you run your halyard to the deck rather than to a cleat on the mast, all the main halyard loads are internalised in the mast. The mast foot/deck is oblivious to the halyard set-up, and feels only the weight of the mast, sail etc and the standing rigging, jib halyard etc. loads.

but what about the 50kN acting downwards at the dead end of the knot at the top of the mast, that brings the total downward force to 200kN thus the compression in the mast must be 200kN which is the same as a 1:1. the 2:1 will be easier to pull up and would require less of a reaction to hold it up there (think of a mainsheet and the difference of 1:1 and multiple purchases), but mast compression does not change. The 50N in the two parts of the 2:1 halyard connected to the sail head are merely transferring the sail load to the mast head - they are how the 100N from the sail get to load the mast at all - what the mast-head experiences is the pull of those two runs of halyard, plus of that going down the mast to the cleat, all loaded to 50N, thus the compressive force is 150N

locking the sail at the top of the mast reduces the compression as you can neglect the halyard loads acting downwards and therefore a smaller reaction is needed. Yes

I think thats all right, my head is spinning to be honest.

Lol ive just confused myself even more.

in reality though, though the compression forces acting down do not run down the centre of the mast. they are offset (the sail at the top) causing a moment and initiating a buckle in the mast and thus the trailing edge of the mast carries compressive load and the front edge will be under tension. You're right, but we've simplified it for the sake of discussion - by and large our conclusions are valid

plus there are many many more factors to think of, such as the fact the force on the sail is a vector not just a parrallel force Again, you're right, but it's a relatively small effect on compression that doesn't invalidate the simplified argument, but does indeed induce bend and very significant effects.

Back to Top
Peaky View Drop Down
Really should get out more
Really should get out more


Joined: 15 Nov 08
Location: United Kingdom
Online Status: Offline
Posts: 2771
Post Options Post Options   Quote Peaky Quote  Post ReplyReply Direct Link To This Post Posted: 18 Mar 09 at 12:34pm

Quite so.

I have drawn a picture - sorry, I'm no artist!

On the left is a standard 1:1 mast.  Centre is a halyard lock.  Right of picture is a 2:1 set up.  Rather than drawing the masts I have assumed the head of the sail is suspended from the ceiling, just for clarity.  So the tensions shown of 2000N, 1000N and 1500N are in fact compression forces own the mast.

 

Back to Top
JohnW View Drop Down
Really should get out more
Really should get out more
Avatar

Joined: 17 Jul 07
Location: United Kingdom
Online Status: Offline
Posts: 552
Post Options Post Options   Quote JohnW Quote  Post ReplyReply Direct Link To This Post Posted: 18 Mar 09 at 1:06pm
deleted - my head hurts


Edited by JohnW
Back to Top
Peaky View Drop Down
Really should get out more
Really should get out more


Joined: 15 Nov 08
Location: United Kingdom
Online Status: Offline
Posts: 2771
Post Options Post Options   Quote Peaky Quote  Post ReplyReply Direct Link To This Post Posted: 18 Mar 09 at 1:51pm

Deleted reply to JohnW



Edited by Peaky
Back to Top
 Post Reply Post Reply Page  <1 23456>

Forum Jump Forum Permissions View Drop Down

Bulletin Board Software by Web Wiz Forums® version 9.665y
Copyright ©2001-2010 Web Wiz
Change your personal settings, or read our privacy policy