New Posts New Posts RSS Feed: Thinking of buying a Wanderer
  FAQ FAQ  Forum Search   Register Register  Login Login

Thinking of buying a Wanderer
 Post Reply Post Reply
Author
  Share Topic Share Topic  Topic Search Topic Search  Topic Options Topic Options
whitsundays View Drop Down
Newbie
Newbie
Avatar

Joined: 21 Oct 20
Location: Australia
Online Status: Offline
Posts: 3 		Post Options Post Options   Quote whitsundays Quote  Post ReplyReply Direct Link To This Post Topic: Thinking of buying a Wanderer
    Posted: 07 Dec 20 at 12:49pm
Look what I found for you. https://www.getmyboat.com.au/journal/how-to/tips-to-avoid-stainless-steel-corrosion-on-boats/. 
Take a few minutes to read this. I am sure this article will help you out.
Whitsundays Yacht Charters
Back to Top
Sam.Spoons View Drop Down
Really should get out more
Really should get out more


Joined: 07 Mar 12
Location: Manchester UK
Online Status: Offline
Posts: 2957 		Post Options Post Options   Quote Sam.Spoons Quote  Post ReplyReply Direct Link To This Post Posted: 26 Oct 20 at 9:58am
IME A2 is not good in seawater* but is fine in fresh, if somebody has bought 'stainless steel' fixings from B&Q, Screwfix or Toolstation to replace something on the boat they will probably be A2 (Toolstation stainless fixings are definitely A2 and are very cheap but it's a limited range of sizes). 

* Actually A2 is usable in seawater if you rinse in fresh water after sailing but will rust if you don't, A4 is much better.
Spice 346 "Flat Broke"
Blaze 671 "supersonic soap dish"
Back to Top
NicolaJayne View Drop Down
Groupie
Groupie


Joined: 01 Mar 19
Online Status: Offline
Posts: 58 		Post Options Post Options   Quote NicolaJayne Quote  Post ReplyReply Direct Link To This Post Posted: 25 Oct 20 at 11:02am
Originally posted by Old bloke

Short answer is dont worry about it.
Stainless steel is really less staining steel and its common to get a little rust staining.
Its a 10 minute job to remove the fitting, then clean and/or replace as required


and a common  problem with  stainless fittings  and rust is poor attention ot detail  with regard to the same grades of stainless being used  - mixing a2 and A4  (304 and 316)  can lead to some interesting   outcomes
Back to Top
Old bloke View Drop Down
Groupie
Groupie


Joined: 03 Nov 17
Online Status: Offline
Posts: 43 		Post Options Post Options   Quote Old bloke Quote  Post ReplyReply Direct Link To This Post Posted: 25 Oct 20 at 8:24am
Short answer is dont worry about it.
Stainless steel is really less staining steel and its common to get a little rust staining.
Its a 10 minute job to remove the fitting, then clean and/or replace as required
Back to Top
wanderer101 View Drop Down
Newbie
Newbie


Joined: 24 Oct 20
Location: Herts
Online Status: Offline
Posts: 1 		Post Options Post Options   Quote wanderer101 Quote  Post ReplyReply Direct Link To This Post Posted: 25 Oct 20 at 7:36am
Hi All, 

I am thinking of buying a Wanderer and have found a possible candidate. It needs some work in general to tidy it up but the one thing that worries me slightly is that I see evidence of rust inside the boat coming through the GRP from the lower right hand shroud screw. 

Would I be right to worry or is there nothing to be concerned at here?
Richard
Back to Top
 Post Reply Post Reply

Forum Jump Forum Permissions View Drop Down

Bulletin Board Software by Web Wiz Forums® version 9.665y
Copyright ©2001-2010 Web Wiz
Change your personal settings, or read our privacy policy