Adhesive Advice
Printed From: Yachts and Yachting Online
Category: General
Forum Name: Repair & maintenance
Forum Discription: Questions & tips on the subject
URL: http://www.yachtsandyachting.com/forum/forum_posts.asp?TID=3890
Printed Date: 12 May 25 at 12:37am
Software Version: Web Wiz Forums 9.665y - http://www.webwizforums.com
Topic: Adhesive Advice
Posted By: andyagar
Subject: Adhesive Advice
Date Posted: 31 Jan 08 at 4:42pm
|
Hi, My Enterprise has suffered a little in todays high winds, the boat turned on to it side when the fittings securing the boat snapped. The impact of the gunwale of the floor has loosened some of the gunhale supports (best described as ribs). These appear to have been secured with some form of adhesive. Any advice on the best way of re-fitting these would be appricated. Thanks. |
Replies:
Posted By: JimC
Date Posted: 31 Jan 08 at 5:55pm
| It rather depends what your Enterprise is made of... More detail please... Are the biots that need repairing Wood to wood, wood to glass, glass to glass, something else? |
Posted By: radixon
Date Posted: 31 Jan 08 at 6:44pm
|
Pictures of the problem will also help. The fact you probably havn't seen the boat is propper light doesn;t help either. As JimC says, more information about what your boat is made of is also required. Out of interest, was your boat secured to the ground with an securing rope/tie downs? ------------- |
Posted By: andyagar
Date Posted: 31 Jan 08 at 8:10pm
|
Sorry for the earlier lack of info, crashed it out in a hurry family commitments and all that! managed to get a look before the light was lost today, no visible damage to the hull or diots except for the remnents of old adhesive. The Hull is Glass and the Biots are wood The boat was secured to the ground with rope onto eys concreted in, but the wind was so severe that the line 10mm polypropolyne snapped, no doubt grit and dirt has got in between the strands and reduced the strength of the line. In saying that a number of other boats in the compound suffered the same fate. |
Posted By: JimC
Date Posted: 31 Jan 08 at 8:41pm
| Clean up all traces of the old adhesive on both surfaces and glue on with SP106 thickened with microfibres and a little silica gel. |
Posted By: Villan
Date Posted: 31 Jan 08 at 9:11pm
No More Nails?  Serious note .. Maybe some form of Epoxy? Even if you cant replicate the original, now you know its a " weak" point, it wont hurt to make sure its well and truly beefed up! ------------- Vareo - 149 "Secrets" http://www.TandyUKServers.co.uk" rel="nofollow - TandyUK Servers |
Posted By: ColH
Date Posted: 01 Feb 08 at 12:01pm
I was watching The Blues Brothers again the other day. You know the bit where Elwood glues the Winnebago's accelerator down? ("This is glue. Strong stuff"). Noticed this time that the label on the can reads "Marine Epoxy"  ------------- |
Posted By: andyagar
Date Posted: 01 Feb 08 at 3:04pm
|
Thanks for the advice so far much appriciated. Had another look today and took some pics, also found that the fall has bent my starboard spreader 1. This shoulder has come clean away.
2, The Gunwale had lifted and sat on top of another Knee and caused a slit split to the hull near the the gunwale.
3. This knee is loose.
4. top of the gunwale in the damaged area.
|
Posted By: Kudlinski
Date Posted: 01 Feb 08 at 6:26pm
|
hi if you new set of spreaders drop me a pm with sizes etc and I can dig you out a pair from boat that I have stripped for bits in the past many thanks. ------------- RS400 866 RS300 381 |
Posted By: JimC
Date Posted: 01 Feb 08 at 7:08pm
|
Cosmetically I can't advise...
With the crack in the topsides you need to abrade the inner surface and put a glass patch over it. probably 4 layers of glass with the first one overlapping an inch from the last bit of crack and each succeeding piece say an inch bigger all round. In all cases you need to make sure the surface you are gluing onto is well abraded and really clean. Acetone can be good to clear up the surface. Make sure your wood knees are well dried out before gluing too - airing cupboard? |